PartSelect 55,284 views 8:00 E4,E5,E6,F1,F2,F3 - Duration: 2:25. The cost of the part is $310.70, so you have to decide if the oven is worth it or it's better to replace the whole oven. Thank you, thank you At $186 a "rescue" you should be able to weather the curent economy. #10 (permalink) 03-31-2012, 05:28 PM Hockstep Junior Member Join Date: Mar ApplianceHelpOnline 351,699 views 3:58 GE Oven - Has F2 error code - Diagnostic & Repair - Duration: 1:53. check over here
The F2 error code beeps when the oven is not in use. This full course of possibilities can help you find the right appliance to match yours Full Story 125 Kitchen Makeovers A ‘Brady Bunch’ Kitchen Overhaul for Less Than $25,000 By Mitchell F7-E1 - Common Switch Wire Is Defective - This error occurs when common wire to latch switch and door switch is shorted. Working...
Those things are a third of the price of a new oven.Technically, a new oven fixes this problem too. Advertisement Autoplay When autoplay is enabled, a suggested video will automatically play next. F13 - Dispenser Circuit Error - Disconnect power and unplug unit to check mechanical linkage from dispenser motor to top of dispenser. F06 - Drive Motor Tachometer Error (Unable to Detect Motor Speed) - Check the shipping system including shipping bolts, spacers, and cables are removed and unplug unit and disconnect power.
The number shown on the paper wiring diagram attached to the back is 348A8003P005. Notify me of new posts by email. Press and hold any key to clear the error code and F2 code should appear. F2 Error Code Whirlpool Washer The oven temperature sensor probe is located in the upper left or upper rear corner.
F4 - Shorted Oven Temperature Sensor (RTD) - Replace oven temperature sensor (RTD). Ge Oven Error Code F3 The oven temperature sensor can be located protruding out of the back wall from inside the oven cavity. The oven sensor is part #WB21T10007. FdL - Door Lock Error - It is possible the door lock mechanism is broken or removed, or the door switch/lock unit has failed. More Bonuses Appliance Princess 7,878 views 3:12 Mr Fix It F2 - Duration: 3:59.
It can likely be removed from inside the oven cavity and tested for proper resistance with an Ohm meter. Ge Oven F9 Error Code While cooking, it gave me an F2 code and would not shut off at all. Under the top panel 2. Check resistance of heating element if present in model, for abnormal reading (infinity).
All rights reserved.
If error continues, replace touch control module. What Does F2 Mean On A Whirlpool Stove Check the wire harness connections to the Central Control Unit (CCU) and the door switch/lock unit. Ge Oven F2 Error Code Self Clean Note: If this failure occurs during high-speed spin, the door will be unlocked after three minutes.
F9 - Oven Door Lock Failure - Check door lock switches and wiring. http://seforum.net/error-code/f2-error-code-on-hot-tub.html ApplianceVideo.com 20,643 views 1:01 GE, General Electric Stove - Has F7 error code - Diagnostic & Repair - Duration: 1:51. Have a great day! Reach up along the inside of the front panel and locate the bottom of the door latch assembly, where there should be a tear-drop shaped tab. Ge Oven Error Codes
F6-E0 - Return Line Not Connected - This error should appear within 60 seconds after power up to appliance. Sign in Transcript 2,239 views 0 Like this video? Loading... http://seforum.net/error-code/eset-error-code-11-gle-error-code-5.html Reach up along the inside of the front panel and locate the bottom of the door latch assembly, where there should be a tear-drop shaped tab.
Make sure there is not a siphon problem and check all hoses for possible leaks. Ge Oven Temperature Sensor F2-E5 - Cancel Key Line Open - Check the connection between the touch pad (keypad) and control board (clock) to make sure it is secure. See Details Avanti, A .7Cf 700 W Microwave Bk Ob (Catalog ...
F1-E6 - Latch Signal Mismatch Error - Disconnect power for at least 30 seconds and then reconnect. F1 - Control Board Failure - Replace control board (clock). You can change this preference below. Ge Oven Error Code F7 by KIM PARINISI Give your feedback by voting on answers 1 votes Didn't find what you are looking for?
Wally // Feb 14, 2016 at 3:12 pm Hi Gene, I have a GE electric range- JBP26WY3WW- during baking the upper oven element wouldn't turn off and I got a F2 I then tried the clean mode again and, as before, the F2 error code appeared after about an hour. Sign in to make your opinion count. have a peek at these guys Add to Want to watch this again later?
Turn off hot and cold water to faucets and unplug the unit before proceeding. In order to fix this problem, the ERC would need to be replaced. Check wire harness connections to the motor, Motor Control Unit (MCU), and Central Control Unit (CCU). If door is latched, disconnect power from unit and check wires and connections.
Unfortunately the model number you provided does not come up. Gene. Does anyone have a fix for this? I took out the control board and carefully removed the covers form the relays.
Gene // Feb 17, 2016 at 2:38 pm Hello Katheryn, Thank you for your question. E4 - Tumbler Rotation Failure - If tumbler rotation speed drops to 0 during a cycle, all outputs will be turned off and this error code will appear. Loading... Check for drain pump failure and clean it of any debris.
I do not think you can do it because the oven functions should be disabled. The content on this web site is for informational purposes only and is not intended to replace an on-site diagnosis from a qualified appliance service technician. F2-E3 - Touch Pad (Keypad) Shorted or Key Held Down Too Long - Select 'cancel' and observe for 60 seconds. Appliance Princess 10,043 views 2:36 Diagnose Kenmore Range Error Code E1 F2, EASY FREE FIX FOR MY RANGE! - Duration: 1:18.
Gene. This case usually involves a cabinet that is completely enclosed on top, back, bottom and sides; thus restricting air flow to the cooling fan. I can't find the control board listed on your link to Appliance Parts Pros. Plug the range back in and wait to see the oven begins to heat.
F32 - Pressure Switch Failure - Select 'cancel' twice to clear error code and disconnect power and unplug unit.